Wi-Fi setup

This page is related to Wi-Fi. Applies to HMP400W, iBX410W, and third-party DSOS players.

Introduction

The HMP400W and iBX410W player models have a built-in wireless network interface controller (WNIC) and can connect to Wi-Fi networks operating in the 2.4 GHz and 5 GHz bands. Some third-party DSOS players may also be Wi-Fi enabled.

Below, you can find more details about how to do the initial Wi-Fi setup by connecting to the player's built-in Wi-Fi access point from a smartphone or computer, and configure the Wi-Fi network details. If the player is connected to a wired network, then you can also set up the Wi-Fi details from Control Center.

The following authentication methods are supported for wireless networks:

• WPA-Personal (WPA-PSK)
• WPA-Enterprise PEAPv0/EAP-MSCHAPv2.

Note:

For WPA-Enterprise advanced Wi-Fi configurations, please refer to the 802.1X Port-Based Network Access Control page.

Initial Wi-Fi setup

This mechanism is only active on a player with firmware 4.6.0 or later that has not yet been configured – for instance, after doing a reset to factory default settings or after flashing the firmware from Recovery mode.

• Once the player is configured to access a wireless network, this mechanism is deactivated for security reasons.
• For players with firmware 4.5.x, it is recommended to connect them to the wired network and update the firmware. Alternatively, you can use the network configurator tool to generate a configuration file and use a USB stick to set up the Wi-Fi network details.

Getting started

 

See more details about how to get started with the HMP400W or the iBX410W.

1. Install the player's Wi-Fi antennas, if necessary.
2. Connect the player to a display (using HDMI or DisplayPort cable).
3. Connect the player to the power supply and wait for the player to boot up.
4. At this point, an unconfigured player will automatically turn on its built-in Wi-Fi access point.
5. For a player that is not connected to the wired network, the splash screen shows the wireless network name and password, for instance:
   

   • • •

Notes:

• The Wi-Fi network of the player is named with the player model (i.e., HMP400 or DSOS) and its serial number.
• The wireless LED on the HMP400W should be blinking yellow indicating that the player accepts a Wi-Fi configuration.
• If the player is connected to the wired network, then you can get the information above by briefly pressing its power/blue button, and then use the network configurator tool to set up the Wi-Fi network details.

Configuration

Next, you need to connect to the player access point and configure its access to your local wireless network, following the steps detailed below, according to the type of device you are using.

From computer

1. Turn on the WIFI on your laptop, tablet, etc.
2. Open the list of wireless networks in range and select the one of the player.
3. Click the "Connect" button.
4. Under the network security key, enter the password displayed on the screen (including the dashes!).
5. Click "Next" and wait for the Wi-Fi configuration page to be automatically opened in your browser.
   • In case it doesn't open, type http://dsos.link in your browser.
6. Enter your local wireless network details (SSID, username, password, etc.) in there.
   • If needed, you can configure a static IPv4 address.
7. Click the "Apply" button and wait for the player to reboot.

Note:

After this, the computer will disconnect from the player's access point and connect back to your Wi-Fi, and after a short delay, the browser page will redirect you to the SpinetiX ARYA site where you can add the player into your account.

From smartphone

1. Turn on the phone camera and scan the QR code.
2. Click on the popup that appears and then click the "Join" button.
3. Go to your device settings, Wi-Fi section.
4. A "Log In" page is displayed.
   • In case that doesn't happen, type http://dsos.link in your mobile's browser.
5. Enter your local wireless network details (SSID, username, password, etc.) in there.
   • If needed, you can configure a static IPv4 address.
6. Click the "Apply" button and wait for the player to reboot.

Final steps

Upon restart, the screen will display something like this:

• • •

Note:

The wireless LED on the HMP400W should be solid green indicating that the player is configured for Wi-Fi and connected to the local wireless network.

Without a DSOS license, the player can only be used with SpinetiX ARYA cloud solution:

1. Open https://arya.spinetix.cloud/setup in a browser.
2. Add the player to your SpinetiX ARYA™ account.
3. Finish setting up the player.

If you have purchased a DSOS license for your player, follow these steps to activate that license.

Setup Wi-Fi in Control Center

If the player is connected to a wired network, you can modify the Wi-Fi configuration from Control Center, as follows:

1. Briefly click the player's blue button to find out all the player addresses.
2. Access the Control Center interface.
   • See the #Troubleshooting section below, for the case when the player is configured to use Wi-Fi, but the preset wireless network is no longer available.
3. Go to Network Settings ⇾ Wi-Fi section.
   • A list of Wi-Fi networks is shown with signal quality and connection status.
4. Click the "Reconfigure" button.
5. 
   Select your local wireless network name (SSID) and the authentication credentials (required, unless it's a public network, without any authentication).
   • If the Wi-Fi network doesn't appear in the list, select "Other..." and manually enter its SSID.
6. Set the IPv4 address to automatic (DHCP) or to manual (if you need to configure a static IPv4 address).
7. Click the "Apply" button and wait for the player to reboot.

Add more Wi-Fi networks

Adding multiple Wi-Fi networks from the same location is not recommended, as the player might lock onto one that doesn't have a strong signal. There are, however, cases when this might be needed, for instance, when you want to configure a wireless network that is not currently in range, like one at a different location or a mobile hotspot (useful for troubleshooting). For that, follow these steps:

1. Use the network configurator tool to configure each new wireless network - make sure to enable each time the option to keep previously configured Wi-Fi networks. A configuration file is generated for each wireless network.
2. Connect to the Control Center.
   • If the player is already in ARYA, you need to remove it from ARYA, to get access to its Control Center.
3. Restore each configuration file.

Troubleshooting

If the preconfigured wireless network is no longer available, you can access the player by doing the following:

1. Connect a network cable to the player.
2. To access the Control Center interface, use the IPv6 address of the player's wired connection: http://[fe80::21d:50ff:fe{XX:XXXX}]/
   • The {XX:XXXX} notation must be replaced with the last six digits of the player serial number, without the curly brackets - e.g., http://[fe80::21d:50ff:fe22:025e]/ for the player with S.N.: 001d5022025e (X2462LY3).
   • If you get redirected to ARYA, then add /user/login?noredirect to the link above - e.g., http://[fe80::21d:50ff:fe22:025e]/user/login?noredirect
3. Follow the steps above to change the Wi-Fi configuration.

---

If connecting to a wired network is not possible, then you need to reset to factory default settings and start from scratch with the initial setup.

See also

• Wi-Fi
• Network configurator tool
• Configure player from USB stick
• 802.1X Port-Based Network Access Control